Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - bflores

Pages: [1] 2 3 4
1
Other / How to install Matebook X Pro FingerPrint Reader on Windows 10 Pro
« on: October 19, 2018, 11:20:46 AM »
The following drivers need to be installed in this order:

Intel Chipset
Intel Serial IO
Intel ME
Intel SGX
Fingerprint

2
Azure / How to force verify a custom domain has been claimed by another Azure Tenant
« on: October 19, 2018, 11:18:17 AM »
How to force verify a custom domain has been claimed by another Azure Tenant

1. Open Windows Powershell as Administrator on local PC, and run the below commands

Install-Module MSOnline
Import-Module MSOnline
connect-msolservice
new-msoldomain –name cognetic.com
get-msoldomainverificationdns –Domainname cognetic.com –Mode DnsTxtRecord
confirm-msoldomain –Domainname cognetic.com –ForceTakeover Force
Get-MsolDomain

3
Intel / How to get Intel NUC Model and BIOS version with Board ID Tool
« on: May 15, 2018, 02:45:34 PM »
(UTITLTY TO GET MODEL AND BIOS VERSION)
Intel NUC Board ID Tool: https://downloadcenter.intel.com/download/26745/

(COMMAND LINES)
wmic baseboard get product //to get model number of NUC

4
Windows / How to remove Windows 10 1803 Update 450MB Left Over Partition
« on: May 08, 2018, 07:18:47 PM »
How to remove Windows 10 1803 Update 450MB Left Over Partition
mountvol d: /d

5
Aruba Networks / How to Setup a new Aruba S1500 Series Switch
« on: April 06, 2018, 11:42:54 PM »
(TO SETUP A NEW ARUBA S1500-12P, S1500-24P or S1500-48P DATA SWITCH)
1. Power On and boot the Mobility Access Switch.
2. Connect a client device (such as a laptop) to the Mobility Access Switch using any Ethernet port in the front. Ensure that DHCP is enabled on the client device and that it is not connected to any other
network.
3. For the S1500 Mobility Access Switch, press and hold the MODE button for 10 seconds or until the four mode status LEDs turn solid green to activate the GUI Quick Setup mode.
5. Confirm that the client device has the IP address in the following range 172.16.0.[1-253] and the DHCP
server has the IP address 172.16.0.254.
6. Open a web browser and enter 172.16.0.254 into the address bar to launch the WebUI Startup Wizard.
7. Follow the on-screen prompts to fill in the required fields to complete the configuration (see Table 1).

You must complete the WebUI Startup Wizard within 10 minutes of invoking GUI Quick-setup mode, else the Mobility Access Switch no longer functions as a DHCP server; you must begin the process again. The timer in the top right corner of the WebUI displays the time remaining.

(HOW TO GET MAC ADDRESS AND SERIAL NUMBER)
1. Putty in and run
2. Enable
3. Show inventory

6
Windows / USB Devices, Mouse, Keyboard and Touchscreen do not work after KB4074588
« on: March 01, 2018, 08:11:14 AM »
USB DEVICES, MOUSE, KEYBAORD AND TOUCHSCREENS DO NOT WORK AFTER KB4074588 IS INSTALLED

(OPTION 1)
- If your mouse is working, just uninstall KB4074588 and reboot.

(OPTION 2)
- Crash the OS 3 times, to get into repair mode, or boot from a windows 10 USB stick and repair.
- Windows Automatic Repair
- Advanced options
- Command Prompt
- Type in and run one the below.
Code: [Select]
dism /online /remove-package /packagename:Package_for_RollupFix~31bf3856ad364e35~amd64~~16299.248.1.17or
Code: [Select]
dism /image:C: /remove-package /packagename:Package_for_RollupFix~31bf3856ad364e35~amd64~~16299.248.1.17
SOURCE: https://support.microsoft.com/en-us/help/4091240/usb-devices-may-stop-working-after-installing-the-february-13-2018-upd

SOURCE: https://answers.microsoft.com/en-us/windows/forum/windows_10-update/after-kb4074588-something-bricked-usb3-support-on/8cb54051-549d-4609-9e27-3a2873d68891?auth=1&ranMID=24542&ranEAID=je6NUbpObpQ&ranSiteID=je6NUbpObpQ-Nvbt2ESA0NSEu3VyJuhXfQ&tduid=(8182e8337556f5ffb52857e3eb4fd234)(256380)(2459594)(je6NUbpObpQ-Nvbt2ESA0NSEu3VyJuhXfQ)()

7
Kaspersky / support.kaspersky.com Dropdown Button Not Working Fix
« on: February 05, 2018, 10:47:00 AM »
support.kaspersky.com Dropdown Button Not Working Fix

Add the below to the content filter allow list.
yandex.st

8
Dell / How to Find and Activate Microsoft Office 2016 or 365 on your new Dell system
« on: October 13, 2017, 04:23:03 PM »
How to Find and Activate Microsoft Office 2016 or 365 on your new Dell system
https://www.dell.com/support/article/us/en/19/sln304490/how-to-find-and-activate-microsoft-office-2016-or-365-on-your-new-dell-system?lang=en

9
Aruba Networks / Default Username and Password for Aruba 2530-24P 2530-48P
« on: September 14, 2017, 09:31:37 AM »
Default Username and Password for Aruba 2530-24P 2530-48P

(DEFAULT CONSOLE LOGIN)
User: manager
Password: blank

10
Aruba Networks / Default Username and Password for Aruba S1500-12P S1500-24P S1500-48P
« on: August 30, 2017, 02:49:39 PM »
Default Console Username and Password for Aruba S1500-12P S1500-24P S1500-48P

(DEFAULT CONSOLE LOGIN)
Username: admin
Password: admin123

(DEFAULT ENABLE PASSWORD)
enable

11
Aruba Networks / Enable DHCP Server on Aruba S1500 Mobility Access Switch
« on: August 15, 2017, 05:36:53 PM »
CREATE THE DHCP SERVER

(ARUBA-S1500) >enable
Password:*******
(ARUBA-S1500) #configure terminal
Enter Configuration commands, one per line. End with CNTL/Z
(ARUBA-S1500) (config) #ip dhcp pool client-dhcp-pool
(ARUBA-S1500) (dhcp server profile "client-dhcp-pool") #network 192.168.42.0 255.255.255.0
(ARUBA-S1500) (dhcp server profile "client-dhcp-pool") #default-router 192.168.42.1
(ARUBA-S1500) (dhcp server profile "client-dhcp-pool") #dns-server 8.8.8.8
(ARUBA-S1500) (dhcp server profile "client-dhcp-pool") #domain-name aruba-cameras.com
(ARUBA-S1500) (dhcp server profile "client-dhcp-pool") #exit
(ARUBA-S1500) (config) #end
(ARUBA-S1500) #write mem
Saving Configuration...
Configuration Saved.

ENABLE THE DHCP SERVER

(ARUBA-S1500) #configure terminal
Enter Configuration commands, one per line. End with CNTL/Z
(ARUBA-S1500) (config) #service dhcp
(ARUBA-S1500) (service dhcp) #exit
(ARUBA-S1500) (config) #end
(ARUBA-S1500) #

12
Office 365 / How to Configure Email Forwarding and Out of Office Vacation Notice
« on: August 01, 2017, 12:48:46 PM »
1.)   Open web browser and go to http://outlook.office365.com

2.)   Login with your email address and password.

3.)   Click the settings wheel


4.)   Scroll down and click on the “Mail” Option
 

5.)   To forward your email or remove email forward, click “Forwarding”
 

6.)   Configure to forward or stop forwarding email.
 

7.)   To create out of office vacation notice, click on “Automatic replies”
 

8.) And Configure


13
Aruba Networks / Aruba Instant Firmware Release 6.5.3.1
« on: July 11, 2017, 11:04:29 AM »
(NOTES)
These are direct file links, to the file.  Not redirected URLs.  You can paste these links into your Aruba Instant Maintenance, Firmware tab, and click update now.

(RELEASE 6.5.3.1)
URL for AP214/215/224/225/228/274/275/277 (Centaurus):
https://dl.dropboxusercontent.com/s/c41p46wzvmdmcuh/Centaurus_6.5.3.1

URL for AP204/205/205H (Taurus):
https://dl.dropboxusercontent.com/s/g9ca557ka3nnbat/Taurus_6.5.3.1

(STEPS TO CREATE YOUR OWN DIRECT LINK)
1.) Download latest firmware from support.arubanetworks.com.
2.) Upload to Dropbox and share / get link.
3.) Modify the shared link to the following format.
From: https://dropbox.com/s/c41p46wzvmdmcuh/Centaurus_6.5.3.1?dl=0
To:  https://dl.dropboxusercontent.com/s/c41p46wzvmdmcuh/Centaurus_6.5.3.1

14
Google / DNSThingy Whitelist Assistant Chrome AddIn - Find web site dependencies
« on: April 21, 2017, 08:09:16 AM »
Whitelist Assistant - Will help build whitelists by finding web site dependencies, and enhances your experience when using DNSthingy web filtering.

https://chrome.google.com/webstore/detail/dnsthingy-assistant/fdmpekabnlekabjlimjkfmdjajnddgpc?hl=en

15
Other / Website Resource Request Services
« on: March 16, 2017, 05:56:04 PM »
https://urlscan.io
urlscan.io is a service which analyses websites and the resources they request. Much like the Inspector of your browser, urlscan.io will let you take a look at the individual resources that are requested when a site is loaded.

The idea behind urlscan.io is to allow even inexperienced users to get a look at what a particular website is requesting in the background. For people new to modern web development, this will often have a certain wow-effect.

Pages: [1] 2 3 4